Recovering uncommon elements from two lists

[john massey]

I have two lists. The numbers of elements in either list is variable. Here is an example to explain what is going in. In all cases the two lists are in ascending order.

{1,3,5,7}-->L1. {1,7}-->L2 // this is done.

{3,5}-->L3 //I need this work done.

Not clear? Ask questions

[DShiznit]

I'm no calculator programmer, but couldn't you just look for and remove common values, so only uncommon ones remain?

[john massey]

I am trying to do that from within a program which is in operation. So, no I cannot do that, yet. That is the reason for the post. You dig?

Questions are always welcome! That helps clarify the problem for others.

[Will_W]

Do the lists need to keep their order?
_________________
TI smote the Beta Testers for their insolence and rested. SynThesIs 14
He doesn't have to wake up, you know. I have a laser, and we have a garbage disposal. - Pintsize

What does the GUI say about his fill level? IT'S OVER 9000!!!

[john massey]

I am not sure. When you get done you could give it one of these SortA(L2.

Forgive me for explaining, there was a time, not long ago ,that I did not know about Sorting in Ascending order.

As before, any question is welcome since it will assist in the convergence on the problem at hand.

[rthprog]

[john massey]

Here is my code with a little while statement to remind my self what I have interpreted your variables to be. I have had troubles with For(N. I changed it "W" because it was free. I further found that each time you use the program you need to set "W" to zero other wise it holds the exit value and the program will not run.

When I ran the program I got an invalid dim error at the end of the "If" statement. I knew if I was going to make a mistake, it would be there. Was it me or you?


0→W
{1,3,5,7}→⌊TEMP4
0→dim(⌊TEMP6
For(W,1,dim(⌊TEMP4
If not(prod(⌊JONL1-⌊TEMP4(W):⌊TEMP4(W→⌊TEMP6(dim(⌊TEMP6+1
End
Output(1,1,⌊TEMP6
Pause
While 0:L3=TEMP6 L1=TEMP4 L2=JONL1 :End

[KermMartian]

[john massey]

Kerm,

Nice to see that the site is up. It was not up for me from 7 to 9 eastern time this AM.

Please note:

1.The post by rthprog above with a suggested solution
2. My response with the actual code
3. My translation From L1, L2 and L3 to my actual variables
4. A bug report on the if statement.

I have trouble understanding your post and ask the following questions:

5. Is rthprog's suggestion your "B"solution?
6. Is my bug report valid, since rthprog made a mistake?
7. Is my bug report invalid, since I made a mistake in translating rthprog's code in the "If" statement?
8. Since we have not heard from rthprog this AM, would you be kind enough, to resolve the mystery and tell me what to do?

Thanks in Advance.

[KermMartian]

Rthprog's solution is a simplified, vectorized example of my B solution; the magic there is the use of the prod( function to find zero'd elements. I believe that your translation, as reproduced below, is correct, such that LTEMP4 = L1, LJONL1 = L2, and LTEMP6=L3.

[john massey]

Kerm,

Thank you very much for your help.

Edit: Kerm,

Here is the code the program previously discussed called GOODFIX is implanted with explanation and question.

[rthprog]

[john massey]

On the 1, matter. I have the following experience. When I run a program for the first iteration of a program everything is fine, if for example "If J=17" 17 is the exit criterion. That is ,one more than the loop count.

On the second iteration of the program J is still 17 and the program exits again. I find that if I set 0-->J everything works fine. When this first happened , I asked myself that is happening. I them ran a little test program with "TEXT(1,1,"Any message that you like" inside the loop. I made "For(I,1,100". Then I checked 'I" on the home screen, it was 101.

I have had this little nit twice in the last 2 days.
So this old man sets letter values to "0" on every occasion.

On the 2. matter. I try to equate the name of the program with what the function does. With a program as complex as this and with a memory that is in the tank, it keeps me from completely loosing it.

Let's take PUT0 for example. It takes the OVER1 with values like {1,3,5,7} and "PUTS0s in OVER1 so it now OVER1 holds {1,0,3,0,5,0,7,0,0,0,0,0,0,0,0,0}

I hope this clears up these two matters, If not fire away with questions.

I hope you find a solution for how to use TEMP6.

[CDI]

[rthprog]

To find unique elements in L1 and L2 and output to L3, use this code (provided that "0" is not a unique element, and that no element is repeated within an individual list):

[john massey]

I appreciate all your help. While I was working on my last post, you people were asking questions. Please, look up a ways to my last previous post and see if you agree with me.

For rthprog. I can see that you code is shorter and it will run faster. Let's concentrate on the question below and if we get the problem solved, I will make your changes in GOODFIX

Lets review the situation. We have created a list called TEMP6. It holds {3,5} Given that we use "For(?,1,Dim(TEMP6" the loop will run twice. The question mark indicates, I do not know what the call the loop counter. There will be two loops in this case.

[rthprog]

[john massey]

After much study, I have boiled down the problem as follows:
You will need this first line of code if you run multiples

[john massey]

Kerm,
I do not know how to use CODE tags. A little torturing, please

{1,0,3,0,5,0,7,0,0,0,0,0,0,0,0,0}→⌊OVER1
ClrHome
{3,5}→⌊TEMP6
SortD(⌊OVER1
sum((⌊OVER1≠0)→dim(⌊OVER1
SortA(⌊OVER1
For(J,1,dim(⌊TEMP6
If J=3:Stop
If ⌊TEMP6(1):⌊OVER1*(⌊OVER1≠J)→⌊OVER1
Output(1,1,"JA
Output(1,5,J
Output(2,1,"OV
Output(2,5,⌊OVER1
Pause
ClrHome
End

Test results JA is 1 not 3
Ov is {0,3,5,7). That part is working since it removed the first element in the list. The question is " how do we recover the values of 3 & 5 from TEMP6

[EmperorWiggy]